R3-RR8 REMOTE CONTROL RELAY CONTROL MODULE

Detail

·Some details are not shown. Please refer to specification sheets for all information.

R3-RR8

Remote I/O R3 Series

REMOTE CONTROL RELAY CONTROL MODULE

Functions & Features
• Controls remote control relays for lighting control with Fieldbus
• Applicable to the remote control relays already installed
• Monitors status of remote control relays with feedback inputs from signal lines
Typical Applications
• Monitors and controls of lighting in buildings
 

MODEL: R3-RR8[1][2]

ORDERING INFORMATION
• Code number: R3-RR8[1][2]
Specify a code from below for each [1] and [2].
 (e.g. R3-RR8W/CE/Q)
• Specify the specification for option code /Q
 (e.g. /C01)

NO. OF CHANNELS
8: 8

[1] COMMUNICATION MODE
S: Single
W: Dual

[2] OPTIONS (multiple selections)
Standards & Approvals
blank: Without CE
/CE: CE marking
Other Options
blank: none
/Q: Option other than the above (specify the specification)

SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating

RELATED PRODUCTS
• Interface Module (model: R3-NC1, NC3, NE1, NM1, NM3, NM4, NDx, NF2, NFL1)
Firmware version V2.00 or higher.
R3-NF2 is available with firmware version V0.04 or higher.,

RECOMMENDED PRODUCTS (OPERATION CHECKED)
Remote control relay:
BR-12D, BR-22D (Mitsubishi Electric)
WR6165 (Panasonic)
Remote control transformer:
BRT-10B, BRT-20B (Mitsubishi Electric)
WR2301 (Panasonic)

GENERAL SPECIFICATIONS
Connection
 Internal bus: Via the Installation Base (model: R3-BSx)
 Output: M3 separable screw terminal (torque 0.5 N·m)
 Internal power: Via the Installation Base (model: R3-BSx)
Screw terminal: Nickel-plated steel
Isolation: Output to internal bus or internal power
Input Data Length: 8 bit, 16 bit selectable with DIP switch
Output data length: 8 bit, 16 bit selectable with DIP switch
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Green LED;
OFF in abnormality; ON in normal operating conditions
Input output status indicator: Red LED;
  1 to 8: Output bit status, turns on with bit set ON.
  9 to 16: Feedback input status, turns on with the inputs ON.

OUTPUT SPECIFICATIONS
Number of output: 8 points
Common: All 8 points (12 terminal)
Rated load voltage: 24 V AC ±10 % (supplied by the remote control transformer)
Load voltage frequency: 50 / 60 Hz
Maximum outputs provided at once: No limit
Output ON duration: 100 msec.

INSTALLATION
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R3-BSx)
Weight: 200 g (0.44 lb)

PERFORMANCE
Data allocation: 1
Current consumption: 40 mA
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(output to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the power supply module)

STANDARDS & APPROVALS
EU conformity:
EMC Directive 
  EMI EN 61000-6-4
  EMS EN 61000-6-2
RoHS Directive
  EN 50581

EXTERNAL VIEW

INPUT OUTPUT DATA BIT & DATA ALLOCATION

DATA ASSIGNMENT

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

M-System Co., Ltd.