R30PA2 TOTALIZED PULSE INPUT MODULE
Tình trạng: In stock
Contact: 0989649965
R30PA2 Remote I/O R30 Series TOTALIZED PULSE INPUT MODULE (Pi 2 points, 32 Bits)
Số lượt xem: 2055
Detail
·Some details are not shown. Please refer to specification sheets for all information.
R30PA2
Remote I/O R30 Series
TOTALIZED PULSE INPUT MODULE
(Pi 2 points, 32 Bits)
Functions & Features
• Space-saving remote I/O module of 2 points input pulse counter
• 32-bit binary data
MODEL: R30PA2S[1]
ORDERING INFORMATION
• Code number: R30PA2S[1]
Specify a code from below for [1].
(e.g. R30PA2S/Q)
• Specify the specification for option code /Q
(e.g. /C01/SET)
NO. OF CHANNELS
2: 2
COMMUNICATION MODE
S: Single
[1] OPTIONS
Other Options
blank: none
/Q: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-9022)
RELATED PRODUCTS
• Interface Module
Model: R30NECT1 (firmware version V1.04.10 or higher)
Model: R30NCIE1 (firmware version V1.01.13 or higher)
• Paperless Recorder
Model: TR30 (firmware version V1.05 or higher)
• PC configurator software (model: R30CFG)
Downloadable at M-System’s web site.
For connecting to PC, use commercially available Mini-B type USB cable. (provided by user)
GENERAL SPECIFICATIONS
Connection
Internal bus: Via the Installation Base (model: R30BS)
Input: M3 separable screw terminal (torque 0.5 N·m)
Internal power supply: Via the Installation Base (model: R30BS)
Solderless terminal: Refer to the drawing at the end of the section.
Recommended manufacturer: Japan Solderless Terminal MFG. Co., Ltd., Nichifu Co., Ltd.
(Solderless terminals with insulation sleeve do not fit.)
Applicable wire size: 0.25 to 0.75 mm2
Screw terminal: Nickel-plated steel
Isolation: Input or reset input or external power to internal bus or internal power
Status indicator LEDs: RUN, ERR
Input status indicator LEDs: Green LED; turns on with input ON
(Refer to the instruction manual.)
Count reset: by inputting one pulse to the reset input terminal, or from host PC/PLC
Count preset: settable from host PC/PLC, or with PC configurator software
INPUT SPECIFICATIONS
Module type: Pulse input, 2 points
Common: Positive or negative common (NPN/PNP), common per 2 points
■ Contact Input / Reset Input
•Open collector input (NPN, PNP)
Rated input voltage: 24 V DC ±10 %; ripple 5 %p-p max.
ON voltage/current: ≥ 16 V DC (input to common) /
≥ 3.7 mA
OFF voltage/current: ≤ 5 V DC (input to common) / ≤ 1 mA
•Voltage Pulse Input
ON voltage/current: ≥ 16 V DC (input to common) /
≥ 3.7 mA
OFF voltage/current: ≤ 5 V DC (input to common) / ≤ 1 mA
Input current: ≤ 5.5 mA per point at 24 V DC
Input resistance: Approx. 4.4 kΩ
ON delay: ≤ 2.0 msec.
OFF delay: ≤ 2.0 msec.
Max input frequency: 100 Hz
Minimum pulse width time requirement: 5 msec. (for both ON and OFF)
Totalized pulse range: 0 to 4,294,967,295 (0 only when the counter is reset)
Max pulse range: 1 to 4,294,967,295
(factory setting: 4,294,967,295)
Count at overflow: 0 or 1 (factory setting: 0)
INSTALLATION
Current consumption: 30 mA max.
Operating temperature: -10 to +55°C (14 to 131°F)
Storage temperature: -20 to +65°C (-4 to +149°F)
Operating humidity: 10 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas or heavy dust
Mounting: Installation Base (model: R30BS)
Weight: 150 g (0.33 lb)
PERFORMANCE
Data allocation: 4
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(input or reset input or external power to internal bus or internal power)
1500 V AC @ 1 minute (power to FG; isolated on the power supply module)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
EN 50581
CONFIGURATOR SOFTWARE SETTING
With configurator software, settings shown below are available.
Refer to the software manual of R30CFG for detailed operation.
EXTERNAL VIEW
TERMINAL ASSIGNMENTS
DATA ALLOCATION
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
M-System Co., Ltd.
Products
-
R1MS-GH3 THERMOCOUPLE & DC INPUT MODULE
R1MS-GH3 Remote I/O R1M Series THERMOCOUPLE & DC INPUT MODULE (8 points, isolated)
-
R1M-P4/MSR PC RECORDER
-
R1M-P4 Remote I/O R1M Series
R1M-P4 Remote I/O R1M Series CONTACT I/O MODULE (4 totalized counter inputs, 8 contact inputs and outputs)
-
R1M-J3/MSR PC Recorders R1M Series
R1M-J3/MSR PC Recorders R1M Series PC RECORDER (RTD or potentiometer input, 8 points)
-
R1M-J3 Remote I/O R1M Series
R1M-J3 Remote I/O R1M Series RTD & POTENTIOMETER INPUT MODULE (8 points)
-
R1M-GH/MSR PC Recorders R1M Series
R1M-GH/MSR PC Recorders R1M Series PC RECORDER (thermocouple or DC input, 16 points)
-
R1MS-GH3/MSR PC Recorders R1M Series
R1MS-GH3/MSR PC Recorders R1M Series PC RECORDER
-
R1D-GH2 THERMOCOUPLE & DC INPUT MODULE
R1D-GH2 Remote I/O R1X Series THERMOCOUPLE & DC INPUT MODULE (16 points; DeviceNet)
-
R1C-GH THERMOCOUPLE & DC INPUT MODULE
R1C-GH Remote I/O R1X Series THERMOCOUPLE & DC INPUT MODULE (16 points; CC-Link Ver.1.10/Ver.2.00)
PRODUCTS LIST
- Signal Conditioners
- 2-wire Signal Conditioners
- Power Transducers
- Indicators
- Tower Lights
- Limit Alarms
- Gateway, Remote IO
- Paperless Recording System
- PC Recorder
- Web Data Loggers
- PID Control Components
- BA&Energy Monitoring Components
- Temperature Controllers
- Electric Actuators
- Lightning Surge Protectors
STATISTIC
Visitor: 1066798Online: 19